How to Clean a Shower: Head, Glass Screen, Tiles, Grout, Drain and Curtain
A step-by-step guide to cleaning every part of your shower, from a clogged shower head and cloudy glass to mouldy grout, a slow drain and the curtain.
TidyGo team9 min read
A shower gets dirty fast. Soap, body oils and hard water leave a cloudy film on the glass, the shower head clogs with limescale, and black mould creeps into the grout and sealant. In London, where the water is hard, it happens even faster. This guide shows you how to clean a shower step by step: the shower head, glass screen, tiles and grout, mould, tray, drain and curtain.
Quick answer: work from top to bottom. Soak the shower head in white vinegar, spray the glass with citric acid or white vinegar and squeegee it, scrub the grout with a bicarbonate of soda paste, pull the hair out of the drain, and wash the curtain in the washing machine with a couple of towels.
What you need
- Citric acid or white vinegar (for limescale on glass and chrome)
- Bicarbonate of soda (for grout and marks)
- Washing-up liquid
- A non-scratch sponge and an old toothbrush
- Microfibre cloths and a squeegee
- Rubber gloves
- A mould remover, if you have black mould
3 safety rules before you start
- Never mix bleach with other cleaners, such as vinegar, limescale remover or ammonia. It makes harmful gas.
- Keep acids off natural stone. Vinegar and other acidic cleaners are risky on marble, limestone and travertine, because the acid "can etch and permanently dull the surface" (Walls and Floors). Use a pH-neutral stone cleaner instead.
- Let air in. Open a window or switch on the extractor fan, and wear gloves.
Step 1: How to clean a shower head
A weak or uneven spray usually means limescale is blocking the holes. Mira Showers says a blocked shower head can "restrict the flow rate and may cause damage to the shower" (Mira Showers).
Handheld shower head (steps from Stroud District Council's repairs guide):
- Unscrew the head from the hose. Keep the rubber washer safe.
- Soak it in white vinegar for at least 30 minutes, ideally about an hour.
- Rinse it, then scrub the holes with an old toothbrush.
- Rinse again, screw it back on and run the shower to flush out any loose limescale.
Fixed shower head: half-fill a plastic bag with white vinegar, tie it over the head so the head sits in the vinegar, and leave it for at least 30 minutes. Then run the shower.
Good to know:
- Don't leave a brass shower head in vinegar for longer than 30 minutes.
- Use white distilled vinegar. Brown vinegar may stain.
- Many household cleaners contain abrasives and chemicals that shouldn't be used on chrome-plated or plastic fittings, Mira warns. Wipe those with mild washing-up liquid and dry them with a soft cloth.
Cleaning the shower head is about health as well as water flow. The Health and Safety Executive says tenants should "regularly clean and disinfect showerheads" to help lower the risk from Legionella bacteria (HSE).
Step 2: How to clean a glass shower screen or door
The white, cloudy film on shower glass is a mix of limescale and soap scum. The Which? science team recommends citric acid for it. Vinegar is "a safe bet", they say, but citric acid is stronger and has no smell (Which?, February 2026).
- Add a couple of spoonfuls of citric acid to a spray bottle of water and shake it.
- Spray the whole screen and leave it for a couple of minutes.
- Scrub with a non-scratch sponge.
- Spray again, then pull a squeegee down the glass in straight strokes. Wipe the squeegee after each stroke.
Use an old toothbrush for the door runners, hinges and seals, where grime collects.
Step 3: How to clean shower tiles and grout
Tiles: wipe them with warm water and a little washing-up liquid, rinse, and dry with a microfibre cloth.
Grout: tile company Fired Earth suggests a paste of 1 part water to 2 parts bicarbonate of soda (Fired Earth).
- Spread the paste along the grout lines.
- Leave it to work. For tough stains, leave it overnight.
- Scrub with a nylon brush or an old toothbrush.
- Rinse with clean, warm water.
Avoid:
- Wire brushes and stiff brushes, which damage grout.
- Vinegar and lemon juice on grout. Harsh cleaners like these can corrode it, so keep them for glass and chrome and rinse well afterwards.
- Lots of bleach. Fired Earth says to use it only on tough grout stains, sparingly, and to rinse thoroughly.
A grout sealant helps keep water and dirt out. It needs putting on again from time to time.
Step 4: How to get rid of mould in a shower
Black spots on the grout and the silicone sealant are mould. It grows where water sits and the air is damp.
- Spray a mould remover on the area and follow the label for how long to leave it.
- Rinse well and dry the area.
- If the mould is deep inside the sealant and won't come out, the sealant needs replacing.
For more help, read our guide on how to get rid of mould in a London home.
Step 5: How to clean the shower tray or floor
Scrub the tray with a non-scratch sponge and washing-up liquid. For marks, use a little bicarbonate of soda paste, then rinse. Don't use scouring pads, which can scratch the surface. If the floor is natural stone, use a pH-neutral stone cleaner only.
Step 6: How to clean a shower drain
A slow or smelly drain is usually blocked with hair and soap.
- Put on gloves and lift off the drain cover.
- Pull out the hair and throw it in the bin.
- Wash the cover and run hot water down the drain.
If it's still slow, try a plughole unblocker and follow the label. Which? tested them and gave two a Best Buy. Both cost less than £5, and one cleared hair within 20 minutes. Never use two drain products together. If the drain is still blocked, call a plumber, or tell your landlord if you rent.
Step 7: How to clean a shower curtain
Most shower curtains can go in the washing machine, but check the label first. These steps are from Mira Showers:
- Take the curtain down and remove the rings.
- Put it in the machine with one or two bath towels. They help scrub the curtain and stop it tearing.
- Wash it on a gentle, warm cycle with your normal detergent.
- Hang it back up to drip-dry.
If the curtain can't be machine washed, scrub it with a damp microfibre cloth and a little bicarbonate of soda, then rinse it with a clean, damp cloth.
How often should you clean a shower?
This simple routine works for most homes:
| When | What to do |
|---|---|
| After every shower | Squeegee the glass and tiles, leave the door or curtain open, and run the fan or open a window |
| Every week | Clean the glass, tiles and tray, and pull the hair out of the drain |
| Every month | Descale the shower head, scrub the grout and wash the curtain |
| When you see it | Treat mould straight away, before it spreads |
How to keep your shower clean for longer
- Use a squeegee after every shower. It takes 30 seconds and stops limescale and soap scum building up. Which? found many squeegees cost under £5.
- Dry it out. Which? says a window vacuum, which sucks the water off the glass, helps "keep mould at bay". A fan or an open window helps too.
- Fight hard water. London's water is hard, so limescale comes back quickly. See our guide on how to remove limescale.
- Clean little and often. A quick weekly clean is much easier than a big scrub every few months. Our daily cleaning routine shows how to fit it in.
Would you rather someone else did it?
TidyGo is a London cleaning company launching soon. Every cleaner passes an ID check, a right-to-work check and a DBS check before their first job.
- A normal clean includes cleaning the shower or bath, and you can tick "Descale taps and shower head" on your checklist. It costs £16.95 an hour per cleaner.
- A deep clean tackles limescale and hard-to-reach places. It costs £20.70 an hour per cleaner.
- With a regular cleaning plan you save 5% paying monthly or 10% paying yearly.
Our cleaners don't do plumbing, so they can't fix a blocked drain or replace sealant. Not sure which clean you need? Read deep clean vs regular clean, or join the waitlist and we'll tell you when we launch.
Questions people ask
What is the best thing to clean a shower with?
For glass and chrome, citric acid or white vinegar removes limescale and soap scum. For grout, use a paste of bicarbonate of soda and water. For tiles and the tray, warm water and washing-up liquid is enough. Use a pH-neutral cleaner on natural stone.
How do you clean a shower head with vinegar?
Unscrew the shower head and soak it in white vinegar for at least 30 minutes, ideally about an hour. Scrub the holes with an old toothbrush, rinse, screw it back on and run the shower. Don't leave a brass shower head in vinegar for longer than 30 minutes.
How do you get limescale off a glass shower screen?
Spray it with citric acid mixed with water, or with white vinegar. Leave it for a couple of minutes, scrub with a non-scratch sponge, spray again and squeegee the glass dry.
How do you get black mould off shower sealant?
Spray a mould remover on it, leave it for the time on the label, then rinse and dry. If the mould is deep inside the sealant, the sealant needs replacing. Never mix bleach with other cleaners.
Can you put a shower curtain in the washing machine?
Most shower curtains can be machine washed, but check the label. Wash it on a gentle, warm cycle with one or two bath towels, then hang it up to drip-dry.
How often should you clean a shower?
Squeegee the glass after every shower, clean the glass, tiles and tray every week, and descale the shower head, scrub the grout and wash the curtain about once a month.
Can you use vinegar on shower tiles?
Not on natural stone such as marble, limestone or travertine, because acid can etch and dull it. Vinegar can also wear away grout over time, so keep it for glass and chrome and rinse well.